pb rohs emds22c2h-100.000m emds22 c 2 h -100.000m series rohs compliant (pb-free) 2.5v 6 pad 3.2mm x 5mm plastic smd lvds mems oscillator frequency tolerance/stability 100ppm maximum over 0c to +70c duty cycle 50 5(%) nominal frequency 100.000mhz logic control / additional output output enable (oe) and complementary output electrical specifications nominal frequency 100.000mhz frequency tolerance/stability 100ppm maximum over 0c to +70c (inclusive of all conditions: calibration tolerance at 25c, frequency stability over the operating temperature range, supply voltage change, output load change, 1st year aging at 25c, reflow, shock, and vibration) aging at 25c 1ppm first year maximum supply voltage +2.5vdc 0.125vdc input current 75ma maximum (excluding load termination current) output voltage logic high (voh) 1.425vdc typical output voltage logic low (vol) 1.075vdc typical differential output voltage (vod) 247mvdc minimum, 350mvdc typical, 454mvdc maximum offset voltage (vos) 1.125v minimum, 1.250v typical, 1.375v maximum rise/fall time 225psec typical, 325psec maximum (measured over 20% to 80% of waveform) differential output error (dvod) 50mvdc maximum duty cycle 50 5(%) (measured at 50% of waveform) offset error (dvos) 50mvdc maximum load drive capability 100 ohms between output and complementary output output logic type lvds logic control / additional output output enable (oe) and complementary output output control input voltage vih of 70% of vcc minimum or no connect to enable output and complementary output, vil of 30% of vcc maximum to disable output and complementary output (high impedance) output enable current 70ma maximum (oe) without load period jitter (deterministic) 0.2psec typical period jitter (random) 2.0psec typical period jitter (rms) 2.5psec typical, 3.5psec maximum period jitter (pk-pk) 25psec typical, 30psec maximum rms phase jitter (fj = 637khz to 10mhz; random) 2.1psec typical rms phase jitter (fj = 1mhz to 20mhz; random) 1.7psec typical rms phase jitter (fj = 1.875mhz to 20mhz; random) 1.5psec typical start up time 10msec maximum storage temperature range -55c to +125c environmental & mechanical specifications esd susceptibility mil-std-883, method 3015, class 2, hbm 2000v flammability ul94-v0 mechanical shock mil-std-883, method 2002, condition g, 30,000g moisture resistance mil-std-883, method 1004 moisture sensitivity level j-std-020, msl 1 resistance to soldering heat mil-std-202, method 210, condition k resistance to solvents mil-std-202, method 215 solderability mil-std-883, method 2003 (pads on bottom of package only) temperature cycling mil-std-883, method 1010, condition b www.ecliptek.com | specification subject to change without notice | rev a 3/12/2011 | page 1 of 5
emds22c2h-100.000m environmental & mechanical specifications thermal shock mil-std-883, method 1011, condition b vibration mil-std-883, method 2007, condition a, 20g mechanical dimensions (all dimensions in millimeters) pin connection 1 output enable (oe) 2 no connect 3 case ground 4 output 5 complementary output 6 supply voltage line marking 1 xxxxx xxxxx=ecliptek manufacturing lot code 0.27 (x4) 0.80 (x2) 1.40 (x6) 1.00 (x6) www.ecliptek.com | specification subject to change without notice | rev a 3/12/2011 | page 2 of 5 3.20 0.15 0.75 0.15 2.54 0.10 1.20 0.10 0.64 0.10 (x6) 1.27 typ (x4) 0.08 max 1.00 0.10 (x6) 5.00 0.15 3 2 1 4 5 6 all t oler ances are 0.1 sug g ested solder p ad la y out solder land (x6) all dimensions in millimeters
emds22c2h-100.000m www.ecliptek.com | specification subject to change without notice | rev a 3/12/2011 | page 3 of 5 output w a veform & timing dia gram v oh v ol v os v ih v il q & q outputs tri-st a te input high imped ance st a te 80% 0v 20% f all time rise time t w t duty cycle (%) = t w /t x 100 t plz t pzl q minus q output q q high imped ance st a te v od v op-p output supply v oltage (v dd ) ground p o w er supply v oltage meter current meter 0.01 f (note 1) 0.1 f (note 1) p o w er supply no connect switch complementar y output t r i-state oscilloscope f requency counter probe 2 (note 2) probe 1 (note 2) t est cir cuit f or t ri-state and complementar y output note 1: an e xter nal 0.01 f cer amic b ypass capacitor in par allel with a 0.1 f high frequency cer amic b ypass capacitor close (less than 2mm) to the pac kage g round and supply v oltage pin is required. note 2: a lo w capacitance (<12pf), 10x atten uation f actor , high impedance (>10mohms), and high bandwidth (>500mhz) passiv e probe is recommended. note 3: t est circuit pcb tr aces need to be designed f or a char acter istic line impedance of 50 ohms . 100 ohms
t min s t max s critical zone t to t l p ramp-up ramp-down t l t p t 25 c to peak t preheat s t l t p temperature (t) time (t) recommended solder reflow methods emds22c2h-100.000m high temperature infrared/convection ts max to tl (ramp-up rate) 3c/second maximum preheat - temperature minimum (ts min) 150c - temperature typical (ts typ) 175c - temperature maximum (ts max) 200c - time (ts min) 60 - 180 seconds ramp-up rate (tl to tp) 3c/second maximum time maintained above: - temperature (tl) 217c - time (tl) 60 - 150 seconds peak temperature (tp) 260c maximum for 10 seconds maximum target peak temperature (tp target) 250c +0/-5c time within 5c of actual peak (tp) 20 - 40 seconds ramp-down rate 6c/second maximum time 25c to peak temperature (t) 8 minutes maximum moisture sensitivity level level 1 www.ecliptek.com | specification subject to change without notice | rev a 3/12/2011 | page 4 of 5
t min s t max s critical zone t to t l p ramp-up ramp-down t l t p t 25 c to peak t preheat s t l t p temperature (t) time (t) recommended solder reflow methods emds22c2h-100.000m low temperature infrared/convection 240c ts max to tl (ramp-up rate) 5c/second maximum preheat - temperature minimum (ts min) n/a - temperature typical (ts typ) 150c - temperature maximum (ts max) n/a - time (ts min) 60 - 120 seconds ramp-up rate (tl to tp) 5c/second maximum time maintained above: - temperature (tl) 150c - time (tl) 200 seconds maximum peak temperature (tp) 240c maximum target peak temperature (tp target) 240c maximum 1 time / 230c maximum 2 times time within 5c of actual peak (tp) 10 seconds maximum 2 times / 80 seconds maximum 1 time ramp-down rate 5c/second maximum time 25c to peak temperature (t) n/a moisture sensitivity level level 1 low temperature manual soldering 185c maximum for 10 seconds maximum, 2 times maximum. high temperature manual soldering 260c maximum for 5 seconds maximum, 2 times maximum. www.ecliptek.com | specification subject to change without notice | rev a 3/12/2011 | page 5 of 5
|
